View LQ150X1DG51_2037931.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..net www..net
records of revision ?k?p?p?t?o?w?p?c?f?t?p spec no. date revised summary note no. page ld - 11z06 dec.10 1999 - - - 1st issue ld - 11z06a jan.20.2000 ??p 7 6 - 2.back light driving ?s note ?t add cautions ? use the lamp inverter ?c ? ld - 11z06b may.26.2000 ??q 6 6 - 2. back light driving lamp current range(min.) : 2.5 ? 3.5 ld - 11z06c sep.04.2000 ??r 5 6 - 1.tft - lcd panel driving current dissipation typ.360 ? 460 (ma) max.530 ? 720 (ma) 5 change tft - lcd panel driving current dissipation typ.460 ? 360 (ma) max.720 ? 530 (ma) ld - 11z06d jan.28.2002 ??s 16 21 17 add packing form add packing form(fig.6) change indication label www..net www..net
ld - 11z06 - 1 1. application this specifications applies to a color tft - lcd module, LQ150X1DG51. ?? these specification sheets are the proprietary product of sharp corporation(?sharp) and include materials protected under copyright of sharp. do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp . ?? the device listed in these specification sheets was designed and manufactured for use in oa equipment . ?? in case of using the device for applications such as contro l and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail - safe functions and redundant system design should be taken . ?? do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support . ?? sharp assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets . ?? contact and cons ult with a sharp sales representative for any questions about this device . 2. overview this module is a color active matrix lcd module incorporating amorphous silicon tft ( t hin f ilm t ransistor). it is composed of a color tft - lcd panel, driver ics, control circuit, power supply circuit and a back light unit. graphics and texts can be displayed on a 1024 ?~ 3 ?~ 768 dots panel with 262,144 colors by supplying 36 bit data signals(6 bit ?~ 2pixel ?~ rgb), four timing signals, +5v dc supply voltage for tft - lcd pan el driving and supply voltage for back light . it is a wide viewing - angle - module (vertical viewing angle:120 ?? horizontal viewing angle:140 ?? ,cr ?? 5). input signal timing conform with 75hz mode of vesa standard. this lcd module with new color filter is suitable for the lcd monitor applications where high vivid color saturation, and high color depth are very important. www..net www..net
ld - 11z06 - 2 3. mechanical specifications parameter specifications unit display size 38 (diagonal) cm 15.0 (diagonal) inch active area 304.1 (h) ?~ 228.1 (v) mm pixel format 1024 (h) ?~ 768 (v) pixel (1 pixel ?? r ?{ g ?{ b dots) pixel pitch 0.297 (h) ?~ 0.297 (v) mm pixel configuration r,g,b vertical stripe display mode normally white unit outline dimensions *1 340.0 (w) ?~ 264.0 (h) ?~ 15.0 (d) mm mass max.1350 g surface treatment anti - glare and hard - coating 2h (haze value = 28) *1.note: excluding back light cables . the thickness of module (d) doesn?t contain th e projection . *2.outline dimension is shown in fig.1 www..net www..net
ld - 11z06 - 3 4. input terminals 4 - 1. tft - lcd panel driving cn1 the module - side connector ?f fx8 - 60s - sv (hirose electric co., ltd.) the user - side connector ?f fx8 - 60p - sv (hirose ele ctric co., ltd.) pin no . symbol function remark pin no . symbol function remark 1 gnd gnd 2 rb0 red even data signal (lsb) 3 rb1 red even data signal 4 rb2 red even data signal 5 rb3 red even data signal 6 rb4 red even data signal 7 rb5 red even data signal (msb) 8 gnd gnd 9 gb0 green even data signal (lsb) 10 gb1 green even data signal 11 gb2 green even data signal 12 gb3 green even data signal 13 gb4 green even data signal 14 gb5 green even data signal (msb) 15 gnd gnd 16 bb0 blue even data signal (lsb) 17 bb1 blue even data signal 18 bb2 blue even data signal 19 bb3 blue even data signal 20 bb4 blue even data signal 21 bb5 blue even data signal (msb) 22 gnd gnd 23 ra0 red odd data signal (lsb) 24 ra1 red odd data signal 25 ra2 red odd data signal 26 ra3 red odd data signal 27 ra4 red odd data signal 28 ra5 red odd data signal (msb) 29 gnd gnd 30 ga0 green odd data signal (lsb) 31 ga1 green odd data signal 32 ga2 green odd data signal 33 ga3 green odd data signal 34 ga4 green odd data signal 35 ga5 green odd data signal (msb) 36 gnd gnd 37 ba0 blue odd data signal (lsb) 38 ba1 blue odd data signal 39 ba2 blue odd data signal 40 ba3 blue odd data signal 41 ba4 blue odd data signal 42 ba4 blue odd data signal 43 gnd gnd 44 gnd gnd 45 gnd gnd 46 vsync vertical synchronous signal 47 hsync horizontal synchronous signal 48 enab data enable signal (signal to settle the display position) 49 gnd gnd (reserve) 50 gnd gnd 51 ckb clock b signal for sampling even data signal 52 cka clock a signal for sampling odd data signal 53 gnd gnd 54 gnd gnd (reserve) 55 ckpol ck edge select for sampling data,enab,hsync 56 mode timing signal select 57 vcc +5v power supply 58 vcc +5v power supply 59 vcc +5v power supply 60 vcc +5v power supply ?| the shielding case is connected with gnd in the module . ?y note 1 ?z in case mode is fixed ?low? , the display start timing is determined by vsync and enab. the vertical display start position and horizontal display start position are determined as described in 7 - 1 - 2, 7 - 1 - 3. do not keep enab ?high? during operation. in case mode is fixed ?high? or ?op en?, the display start timing is determined by only enab. ?y note 2 ?z in case ckpol is ?low? in case ckpol is ?high? data,enab,hsync cka,ckb the rising edge the falling edge sampling timing www..net www..net
ld - 11z06 - 4 4 - 2. back lig ht driving cn2, cn4 the module - side connector : bhsr - 02vs - 1(jst) the user - side connector : sm02b - bhss - 1 - tb(jst) pin no. symbol function 1 ?u high - 1 power supply for lamp (high voltage side 1) 2 ?u high - 2 power su pply for lamp (high voltage side 2) cn3, cn5 the module - side connector : bhr - 02vs - 1(jst) the user - side connector : sm02(4.0)b - bhs - 1 - tb(jst) pin no. symbol function 1 ?u low - 1 power supply for lamp (low voltage side 1) 2 ?u low - 2 power supply for lamp (low voltage side 2) 5. absolute maximum ratings parameter symbol condition ratings unit remark input voltage v i ta=25 ?? ?| 0.3 ?`?{ 5.5 ?u ?y note1 ?z +5.0v supply voltage vcc ta=25 ?? 0 ?` ?{ 6 ?u storage temperature tstg ?| ?| 25 ?` ?{ 60 ?? ?y note2 ?z operating temperature (ambient) topa ?| 0 ?` ?{ 50 ?? ?y note1 ?z cka, ckb, ra0 ?` ra5, ga0 ?` ga5, ba0 ?` ba5, rb0 ?` rb5, gb0 ?` gb5, bb0 ?` bb5, hsync, vsync, enab, mode, ckpol ?y note2 ?z humidity ?f 95%rh max. ( ta ?? 40 ?? ) maximum wet - bulb temperature at 39 ?? or less ( ta>40 ?? ) no condensation. ?@ ?@ ?a ?a ?@ ?@ ?a ?a cn2 tft lcd module cn3 cn4 cn5 www..net www..net
ld - 11z06 - 5 6. electrical characteristic s 6 - 1. tft - lcd panel driving ta ?? 25 ?? parameter symbol min. typ. max. unit remark vcc supply voltage vcc +4.5 +5.0 +5.5 v ?y note1 ?z current dissipation icc ?| 360 530 ma ?y note2 ?z ? 3,4 permissive input ripple voltage v rf ?| ?| 100 mvp - p vcc=+5.0v input voltage (low) v il gnd ?| 0.6 v ?y note3 ?z input voltage (high) v ih 2.6 vcc v ?y note3 ?z input current (low) i il ?| ?| 10 ? a v i =gnd ?y note3,5 ?z ?| ?| 400 ? a v i =gnd ?y note4 ?z input current (high) ?| ?| 10 ? a v i =vcc ?y note3 ?z i ih ?| ?| 600 ? a v i =vcc ?y note4 ?z ?| 3.3(v) logic is recommended as input signals . ?y note1 ?z on - off conditions for supply voltage 0 ?? t1 ?? 10ms 0 ?? t2 ?? 10ms 0 ?? t3 ?? 1s t4 ?? 1s vcc - dip conditions 1) 2.7v ?? vcc ?? 4.5v td ?? 10ms 2) vcc ?? 2.7v vcc - dip conditions should also follow the on - off conditions ?y note2 ?z typical current situation : 16 - gray - bar pattern. vcc=+5.0v,ck:32.5mhz,th:20.7 ? s gray scale : gs(4n) n=0 ?` 15 the explanation of each gray sc ale ,gs(4n), is described below section (8). ?y note3 ?z cka, ckb, ra0 ?` ra5, ga0 ?` ga5, ba0 ?` ba5, rb0 ?` rb5, gb0 ?` gb5, bb0 ?` bb5, hsync, vsync, enab ?y note4 ?z mode ckpol input circuit of mode is shown in right figure. input circuit of mode is shown in right figure. t1 t2 t3 4.5v 4.5v vcc data vcc data t4 2.7v 2.7v vcc td 2.7v 4.5v r g b g s 0 r g b g s 4 r g b g s 8 r g b g s 5 6 r g b g s 6 0 . . . . to control asic 20k ?? 3.3k ?? 10k ?? vcc internal power supply (3v) mode to control asic 10 k ?? ckpol 33 ?? www..net www..net
ld - 11z06 - 6 6 - 2. back light driv ing ??p??q the back light system is an edge - lighting type with four ccfts (cold cathode fluorescent tube). the characteristics of the lamp are shown in the following table . the value mentioned below is at the case of one ccft . ccft model name : fl - 26314(c9) - lq150 (toa elevam co.,ltd) parameter symbol min. typ. max. unit remark lamp current range i l 3.5 6.0 6.5 marms ?y note1 ?z ??q lamp voltage v l ?| 630 ?| vrms ta=25 ?? lamp power consumption p l ?| 3.8 ?| ?v ?y note2 ?z lamp frequency f l 20 60 70 khz ?y note3 ?z kick - off voltage vs ?| ?| 800 vrms ta=25 ???y note4 ?z ?| ?| 1420 vrms ta=0 ???y note4 ?z lamp life time l l 50000 ?| ?| hour ?y note5 ?z ?y note1 ?z a lamp can be light in the range of lamp current shown above . maximum rating for current is measured by high frequency current measurement equipment connected to v low at circuit showed below . (note : to keep enough kick - off voltage and necessary steady voltage for ccft .) lamp frequency : 20 ?` 70khz ambient temperature : 0 ?` 50 ?? module ?p or 2 1 or 2 inverter ?` ?` * cn3,cn5 is v low cn3,cn5 cn2,cn4 ?y note2 ?z referential data per one ccft by calculation ( i l ?~ v l ) . the data doesn?t include loss at inverter . ?y note3 ?z lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. therefore, adjust lamp frequency, and keep inverter as far as from module or use electronic shielding between inve rter and module to avoid interference. ?y note4 ?z kick - off voltage value is described as the index in the state of lamp only. the kick - off voltage is estimated to be risen up as approx. +200v in the state of module only, and the further rise up can be seen acc ording to the assembling status of user cabinet. please set the kick - off voltage of inverter to avoid the lighting failures in the state of operation. please design the inverter so that its open output voltage can be connected for more than 1 second to sta rtup. otherwise, the lamp may not be turned on. but, please set as 100ms when the ambient luminance around the lamp is more than 1 lux. ?y note5 ?z lamp life time is defined as the time when either ?@ or ?a occurs in the continuous operation under the condition of ta=25 ?? and i l =6.0 ?} 0.5marms . ?@ brightness becomes 50% of the original value under standard condition . ?a kick - off voltage at ta=0 ?? exceeds maximum value, 1420vrms . ?s note ?t the performance of the back light, for example life time or brightness, is muc h influenced by the characteristics of the dc - ac inverter for the lamp .when you design or order the inverter, please make sure that a poor lighting www..net www..net
ld - 11z06 - 7 caused by the mismatch of the back light and the inverter (miss - lighting, flicker, etc.) never occurs . whe n you confirm it, the module should be operated in the same condition as it is installed in your instrument . ? ?p use the lamp inverter power source incorporating such safeguard as overvoltage/overcurrent protective circuit or lamp voltage waveform detection circuit, which should have individual control of each lamp. in case one circuit without such individual control is connected to more th an tw o lamps, excessive current may flow into one lamp when the other one is not in opera tion. 7. timing characteristics of input signals 7 - 1. h - v mode (mode = ?low? ) timing diagrams of input signal are shown in fig.2 - 1 (ckpol = ?low?), fig.2 - 2 (ckpol = ?high?). 7 - 1 - 1. timing characteristics parameter symbol min. typ. max. unit remark clock a frequency 1/tc 25 32.5 40 mhz clock b high time tch 9 ?| ?| ns low time tcl 9 ?| ?| ns duty ratio tch/tcl 0.67 1.00 1.50 phase difference tcp - 4 0 +4 ns data setup time tds 5 ?| ?| ns hold time tdh 5 ?| ?| ns horizontal cycle th 16.6 20.7 ?| ? s sync. signal 528 672 860 clock pulse width thp 2 68 ?| clock horizontal data start thbp ?| ?| ?| clock ?y note1 ?z setup time ths 5 ?| ?| ns hsync - ck hold time thh 5 ?| ?| ns vertical cycle tv ?| 16.7 ?| ms ?y note2 ?z sync. signal 773 806 990 line pulse width tvp 1 6 ?| line vertical data start tvbp 35 35 35 line hsync - vsync phase difference tvh 1 ?| th - thp clock ?y note1 ?z horizontal data start is determined only by data enable signal. ?y note2 ?z in case of lower frequency, the deterioration of display quality, flicker etc may be occurred . 7 - 1 - 2. horizontal display position the horizontal display position is determined by enab signal and the input data corresponding to the rising edge of enab sig nal is displayed at the left end of the active area . parameter symbol min. typ. max. unit remark enab signal setup time tes 5 ?| tc - 10 ns hold time teh 5 ?| ?| ns pulse width tep 10 512 512 clock hsync - enab phase difference the thp+1 148 th - 512 clock 7 - 1 - 3. vertical display position the vertical display start position is the 35th line from the falling edge of vsync .(cf. fig.2 - 1 or 2 - 2) www..net www..net
ld - 11z06 - 8 7 - 2. enab mode (mode = ?high? or ?open? ) timing diagrams of input signal are shown in fig.3 - 1 (ckpol = ?low?), fig.3 - 2 (ckpol = ?high?) 7 - 2 - 1. timing characteristics parameter symbol min. typ. max. unit clock a frequency 1/tc 25 32.5 40 mhz clock b high time tch 9 ?| ?| ns low time tcl 9 ?| ?| ns duty ratio tch/tcl 0.67 1.00 1.50 phase difference tcp - 4 0 +4 ns data setup time tds 5 ?| ?| ns hold time tdh 5 ?| ?| ns data enable setup time tes 5 ?| tc - 10 ns signal hold time teh 5 ?| ?| ns 16.6 20.7 ?| ? s horizontal period th 528 672 860 clock horizontal period (high) thp 10 512 512 clock vertical period tv 770 806 990 line vertical blanking width tvb 2 38 222 line ?y note ?z in case of using the long vertical period, the deterioration of display quality, flicker etc., may be occurred. 7 - 3. input data signals and display position on the screen graphics and texts can be displayed on a 1024 ?~ 3 ?~ 768 dots pa nel with 262,144 colors by supplying 36 bit data signal (6bit/color [64 gray scale] x 3 x 2 pixels) . da(1,1 ) db(1,1 ) da(2,1) da(1,2) db(1,2 ) da(1,3 ) da(1,7 68) db(512,1 ) ?q ?f ?a db(512,768) ra ga ba rb gb bb ( ?p?p ) ( ?p ,1) two pixel-data are sampled at the same time. ?? da ?f ra0 ?` ra5, ga0 ?` ga5, ba0 ?` ba5 ?? db ?f rb0 ?` rb5, gb0 ?` gb5, bb0 ?` bb5 display position of input data ?i h,v ?j www..net www..net
h orizontal sync signal (hsync) clock signal a clock signal b th s c0* c1* thp number of data th data a (ra0 ?` ra5,ga0 ?` ga5 ba0 ?` ba5) 0.6v da511 da512 invalid invalid thbp db511 db512 invalid invalid data b (rb0 ?` rb5,gb0 ?` gb5 bb0 ?` bb5) 2.6v venab signal the 0.6v tds tdh da1 da2 da3 2.6v db1 db2 db3 2.6v tch tcl tc 2.6v 0.6v 0.6v 0.6v 0.6v 2.6v tes tep da1 da2 da3 db1 db2 db3 fig. 2 - 1 input signal waveforms(h - v mode ,ckpol= ?g low ?h ) data signal (ra0 ?` ra5,ga0 ?` ga5,ba0 ?` ba5) (rb0 ?` rb5,gb0 ?` gb5,bb0 ?` bb5) dh1 dh2 dh3 dh765 dh768 inval id invalid horizontal sync signal (hsync) tvh tvd number of data 0 line 1 line 34 line (number of horizontal sync ?j 0.6v tvbp tv 0.6v vertical sync sig nal (vsync) tvp 0.6v 2.6v 0.6v 0.6v 35 line 2.6v th h teh 2.6v 0.6v clock signal a 0.6v tc p(+) 0.6v 0.6v tc p( - ) clock signal b clock signal a clock signal b ld - 11z06 - 9 www..net www..net
horizontal sync signal (hsync) clock signal a clock signal b th s c0* c1* thp number of data th data a (ra0 ?` ra5,ga0 ?` ga5 ba0 ?` ba5) 0.6v da511 da512 invalid invalid thbp db511 db512 invalid invalid data b (rb0 ?` rb5,gb0 ?` gb5 bb0 ?` bb5) 2. 6v venab signal the 0.6v tds tdh da1 da2 da3 2.6v db1 db2 db3 2.6v tch tcl tc 2.6v 0.6v 0.6v 0.6v 0.6v 2.6v tes tep da1 da2 da3 db1 db2 db3 fi g. 2 - 2 input signal waveforms(h - v mode ,ckpol= ?g high ?h ) data signal (ra0 ?` ra5,ga0 ?` ga5,ba0 ?` ba5) (rb0 ?` rb5,gb0 ?` gb5,bb0 ?` bb5) dh1 dh2 dh3 dh765 dh768 invalid invalid horizontal sync signal (hsync) tvh tvd number o f data 0 line 1 line 34 line (number of horizontal sync ?j 0.6v tvbp tv 0.6v vertical sync signal (vsync) tvp 0.6v 2.6v 0.6v 0.6v 35 line 2.6v th h teh 2.6v 2.6v 2 .6v clock signal a 2 .6v tc p(+) 2 .6v 2 .6v tc p( - ) clock signal b cl ock signal a clock signal b ld - 11z06 - 10 www..net www..net
fig. 3 - 1 input signal waveforms(enab mode ,ckpol= ?g low ?h ) data signal ra0 ?` ra5 ga0 ?` ga5 ba0 ?` ba5 rb0 ?` rb5 gb0 ?` gb5 bb0 ?` bb5 dh767 dh768 number of data invalid dh1 dh2 dh3 tv invalid 2.6v dh1 dh2 dh3 2.6v ld - 11z06 - 1 1 enab signal 0.6v tvb data signal a ra0 ?` ra5 ga0 ?` ga5 ba0 ?` ba5 enab signal clock signal a clock signal b data signal b rb0 ?` rb5 gb0 ?` gb5 bb0 ?` bb5 0.6v th 2.6v tes thp 2.6 tds tdh number of data da1 da2 da3 da511 da512 2.6v db1 db2 db3 db511 db512 2.6v tch tcl 2.6v 0.6v 0.6v 0.6v 0.6 v invalid invalid invalid invalid tc 2.6v te h (1line) 0.6v clock s ignal a 0.6v tc p(+) 0.6v 0.6v tc p( - ) clock signal b clock signal a clock signal b (2line) www..net www..net
fig. 3 - 2 input signal waveforms(enab mode ,ck pol= ?g high ?h ) data signal ra0 ?` ra5 ga0 ?` ga5 ba0 ?` ba5 rb0 ?` rb5 gb0 ?` gb5 bb0 ?` bb5 dh767 dh768 number of data invalid dh1 dh2 dh3 tv invalid 2.6v dh1 dh2 dh3 2.6v (1line) ld - 11z06 - 1 2 enab signal 0.6v tvb data signal a ra0 ?` ra5 ga0 ?` ga5 ba0 ?` ba5 enab signal clock signal a clock signal b data signal b rb0 ?` rb5 gb0 ?` gb5 bb0 ?` bb5 0.6v th 2.6v tes thp 2.6 tds tdh number of data da1 da2 da3 da511 da512 2.6v db1 db2 db3 db511 db512 2.6v tch tcl 2.6v 0.6v 0.6v 0.6v 0.6 v invalid invalid invalid invalid tc 2.6v te h 0.6v 2 .6v c lock s ignal a 2 .6v tc p(+ ) 2 .6v 2 .6v tc p( - ) c lock s ignal b (2line) c lock s ignal a c lock s ignal b www..net www..net
ld - 11z06 - 13 8. input signals, basic display colors and gray scale of each color colors & data signal gray scale gray ra0 ra1 ra2 ra3 ra4 ra5 ga0 ga1 ga2 ga3 ga4 ga5 ba0 ba1 ba2 ba3 ba4 ba5 scale rb0 rb1 rb2 rb3 rb4 rb5 gb0 gb1 gb2 gb3 gb4 gb5 bb0 bb1 bb2 bb3 bb4 bb5 black ?| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue ?| 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 green ?| 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 cyan ?| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 red ?| 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 magenta ?| 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow ?| 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 white ?| 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? gs1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 darker gs2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? a a a a a a a a brighter gs61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 gs62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 red gs63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? gs1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 darker gs2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 ? a a a a a a a a brighter gs61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 gs62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 green gs63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? gs1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 darker gs2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 ? a a a a a a a a brighter gs61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 gs62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 blue gs63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 :low level voltage, 1 : high level voltage each basic color can be displayed i n 64 gray scales from 6 bit data signals. according to the combination of total 18 bit data signals, the 262,144 - color display can be achieved on the screen. basic color gray scale of red gray scale of green gray scale of blue www..net www..net
ld - 11z06 - 14 9. optical characteristics ta=25 ?? , vcc=+5v parameter symbol condition min. typ. max. unit remark horizontal ?? 21, ?? 22 60 70 ?| deg. ?? 11 45 60 ?| deg. vertical ?? 12 cr ?? 5 50 60 ?| deg. ?y note1,4 ?z horizontal ?? 21, ?? 22 cr ?? 10 50 65 ?| deg. ?y note1,4 ?z vertical ?? 11 35 50 ?| deg. viewing angle range ?? 12 40 50 ?| deg. contrast ratio ?b?q n ?? =0 ?? 200 300 ?| ?y note2,4 ?z response rise ?? r ?| 10 25 ???? ?y note3,4 ?z time decay ?? d ?| 35 50 ???? chromaticity of x 0.283 0.313 0.343 ?y note4 ?z white y 0.299 0.329 0.359 luminance of white y ?k 1 180 220 ?| cd/m 2 i l =6.0marms ?y note4 ?z white uniformity ?a w ?| ?| 1.35 ?y note5 ?z ?| the measurement shall be executed 30 minutes after li ghting at rating . (typical condition:i l =6.0marms) the optical characteristics shall be measured in a dark room or equivalent state with the method shown in fig.6 below . photodetector (bm - 5a:topcon) fig. 4 optical characteristics measurement method center of the screen ?s?e?s?|?k?b?c module ?s?o?o???? ?e???????????q?? ?k?b?c panel www..net www..net
ld - 11z06 - 15 ?y note1 ?z definitions of viewing angle range: ?y note2 ?z definition of contrast ratio: the contrast ratio is defined as the following . contrast ratio (cr) ?? ?y note3 ?z definition of response time: the response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white" . ?y note4 ?z this shall be measured at center of the screen . ?y note5 ?z definition of white uniformity: white uniformity is defined as the following with five measurements (a ?` e) . luminance (brightness) with all pixels white luminance (brightness) with all pixels black a b c d e pixel 256 512 768 pixel 192 384 576 maximum luminance of five points (brightness) minimum luminance of five points (brightness) ?aw?? www..net www..net
ld - 11z06 - 16 10. handling precautions a) be su re to turn off the power supply when inserting or disconnecting the cable . b) be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist . c) since the front polarize is easily damaged, pay atten tion not to scratch it . d) since long contact with water may cause discoloration or spots, wipe off water drop immediately . e) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. . f) since the panel is made of g lass, it may break or crack if dropped or bumped on hard surface. handle with care . g) since cmos lsi is used in this module, take care of static electricity and take the human earth into consideration when handling . h) make sure the four mounting holes of the module are grounded sufficiently. take electro - magnetic interference (emi) into consideration. i) the module has some printed circuit boards (pcbs) on the back side. take care to keep them form any stress or pressure when handling or instal ling the module; otherwise some of electronic parts on the pcbs may be damaged. j) observe all other precautionary requirements in handling components. k) when some pressure is added onto the module from rear side constantly , it causes display non - u niformity issue , functional defect , etc . so , please avoid such design. l) when handling lcd modules and assembling them into cabinets, please be noted that long - term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the lcd modules. 11. packing form ? 4 form ?@ form ?a product country japan taiwan piling number of cartons 5 cartons 5 cartons packing quantity in one carton 5 modules 5 modules carton size [mm] 410 (w) ?~ 500 (d) ?~ 240 (h) 420 (w) ?~ 510 (d) ?~ 225 (h) total mass of one carton filled with full modules ?w?x?t?o g ?x?r?o?o g packing form is shown fig .5 fig .6 www..net www..net
ld - 11z06 - 17 12 ?d reliability test items no. test item conditions 1 high temperature storage test ta=60 ?? 240h 2 low temperature storage test ta= - 25 ?? 240h 3 high temperature & high humidity operation test ta=40 ?? ; 95%rh 240h (no condensation) 4 high temperature operation test ta=50 ?? 240h (the panel temp. must be less than 60 ?? ) 5 low temperature operation test ta=0 ?? 240h 6 vibration test (non - operating) frequency : 10 ?` 57hz/vibration width (one said) : 0.075mm : 58 ?` 500hz/gravity : 9.8m/s 2 sweep time : 11minutes test period : 3 hours (1 hours for each direction x,y,z) 7 shock test (non - operating) max, gravity : 490m/s 2 pulse width : 11 ms, sine wave direction : ?} x, ?} y, ?} z once for each direction ?y result evaluation criteria ?z under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function . 13 ?d others 1) lot no. and indication label ? 4 2) adjusting volume have been set optimally before shipment, so do not change any adjusted value. if adjusted value is changed, the specification may not be satisfied. 3) disassembling the module can cause permanent damage and should be strictly avoided. 4) please be careful since image retention may occur when a fixed pattern is displayed for a long time. 5) the chemical compound that causes the destruction of ozone layer is not being u sed. 6) when any question or issue occurs, it shall be solved by mutual discussion. how to express lot no. a production month (1 ?` a production year (the last figures of the serial no. administration no. sharp LQ150X1DG51 21 300004_ made in ???????? model no. lot no. japan or taiwan www..net www..net
ld - 11z06 - 18 ?? carton storage condition temperature 0 ?? to 40 ?? humidity 95%rh or less reference condition : 20 ?? to 35 ?? , 85%rh or less (summer) : 5 ?? to 15 ?? , 85%rh or less (winter) ?e the total storage time (40 ?? ,95%rh) : 240h or less sunlight be sure to shelter a product from the direct sunlight. atmosphere harmful gas, such as acid and alkali which bites electronic components and/or wires, must not be detected. notes be sure to put cartons on palette or base, don?t put it on floor, and store them with removing from wall. please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits o f natural environment. storage period 1 year www..net www..net
www..net www..net
www..net www..net
www..net www..net

▲Up To Search▲

Price & Availability of LQ150X1DG51

	To Download LQ150X1DG51 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .